MARINE Premium Wood Sealer in Clear and Ready Mixed Colors
MARINE Premium Wood Sealer in Clear and Ready Mixed Colors
MARINE is a premium waterproofing dock sealer & deck stain. It deeply penetrates the surface to protect and stabilize wood in high-moisture locations. It is an Eco-friendly wood finish, with ultra-low VOCs, and is safe to use around pets, plants & people .
- Formulated for use on wood near open water, non-hazardous to aquatic life
- Recommended for wood boat docks, pool decks, walkways
- Piers & outdoor furniture near ocean, lakes, ponds & rivers
GREAT FOR USE ON
GREAT FOR USE ON
SEAL-ONCE® has been leading the innovation in the use of nanotechnology to create long-lasting, Eco-friendly wood sealers & tinted wood stains since 2005. MARINE Premium wood sealer and dock stain is specifically formulated to provide the highest level of protection for wood structures, situated near open water. Wood used on boat docks, decks, and retaining walls near rivers, lakes, ponds or the ocean is subjected to near constant moisture. MARINE provides the highest level of protection in those environments. It is a great investment to extend the useful life of wood subjected to these harsh marine conditions, is non-hazardous to aquatic life.
SEAL-ONCE® MARINE Premium Waterproofing Wood Sealer & Stain is designed to protect & stabilize marine wood against water damage, salt water spray & decay. Unlike many top-coat sealers on the market today, it penetrates wood below the surface, coating the wood fibers at the cellular level, which creates a long-lasting, flexible, breathable barrier. It provides long-lasting protection from the inside out.
Clear formula allows wood to age naturally without decay, morphing to a rich silver-gray over time. Seal-Once Marine, when tinted as a wood stain, gives added protection from decay. Prevents long-standing water accumulation for up to 10 years on vertical & up to 6 years on horizontal surfaces.
FEATURES
FEATURES
- Safe for use over open water and non-hazardous to aquatic life
- Special formulation for wood docks & decks near open water
- Extends useful life of boat docks, pool decks & resists salt water spray
- Advanced nanotechnology provides superior protection against water
- Non-film forming – will not cause surface to become slippery
- Water based, low VOC formula is safe for use near water & marine life
- Approximate coverage: 250-350 sq. ft./gallon per coat. Based on surface porosity.
DATA SHEETS
DATA SHEETS
Collapsible content
APPLICATIONS
- Do not use if air or surface temperature is below 45°F/7.22°C or above 95°F/35°C.
- Do not apply in rain or when rain is expected within 12-24 hours. For all stains (including Ready-Mixed), intermix gallons and stir to ensure color consistency.
- DO NOT THIN. Mix well. Stir contents or shake thoroughly prior to use.
- Test a small area to ensure acceptable appearance and penetration.
- Apply first coat with a synthetic brush; pump-up garden sprayer; air-assisted; and/or airless sprayer. Use 15-17 tip and medium to coarse spray pattern. When spraying, always back brush for best results.
- Second coat can be applied once first coat has penetrated but is still damp. Second coat must be applied within one hour of applying first coat.
- For best results, apply in the shade and out of direct sunlight.
- When applying in direct sunlight and wood surface is hot, spray with a mist of water and apply SEAL-ONCE MARINE immediately on dampened surface.
- Apply to all surfaces.
- Do not use with other waterproofing products.
- Remove excess stain sitting or puddling on the surface. Back brush or use a rag to wipe away any runs, drips, or puddles that have not soaked in.
- Allow approximately 2-3 hours for surface to dry, depending on temperature and humidity, before subjecting surface to light foot traffic.
- Allow 12-24 hours for full cure, depending on temperature and humidity.
- When recoating, apply as soon as previous coat has penetrated and surface is damp, not wet. Second coat must be applied within one hour of applying first coat.Allow approximately 2-3 hours for surface to dry, depending on temperature and humidity, before subjecting surface to light foot traffic.
- Allow 12-24 hours for full cure, depending on temperature and humidity.
- When recoating, apply as soon as previous coat has penetrated and surface is damp, not wet. Second coat must be applied within one hour of applying first coat.
- Clean application equipment with warm soapy water.
- Disposal: soap and water cleanup; no special disposal procedure needed.
- Store above 32°F/0°C to protect from freezing.
- Shelf life (unopened): 3 years
PRODUCT DETAILS
- All surfaces should be cleaned before sealing for best penetration and performance.
- Wet the surface.
- Clean the surface with a solution of 1/2 cup Seal-Once All Wood Cleaner to 1 gallon of water Apply this solution to the wood with a garden pump sprayer.
- Let the solution sit for 15-20 minutes. Do not let the cleaner dry. Keep it wet.
- Power wash the cleaning solution from the wood. To prevent damaging the wood do not exceed 500psi. Keep the nozzle 1-2 feet away from the surface.
- Rinse thoroughly.
- Test absorbency after cleaning by sprinkling water on surface. If the water does not readily penetrate the surface, stripping will be necessary to remove old coatings.
- Let the surface dry 1-2 dry days before application of Seal-Once.